Medium Duty Trolley Operator for Standard Lift Sectional Doors Model MT is a Medium-Duty Logic trolley operator for standard lift sectional doors. It features a high-starting torque motor a compact design quick-gliding rail spacers and a quick-mount swivel header bracket. MEDIUM-DUTY LOGIC TECHNOLOGY Added Value UL 325-2010 compliant Medium-Duty Logic programmable integrated circuit board Built-in 3-channel 315 MHz radio receiver accepts up to 20 Chamberlain Security or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation Programmable C2 or B2 wiring options (B2 requires CPS-U CPS-UN4, or CPS-EI) Integrated Timer-to-Close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices with CPS-U CPS-UN4, or CPS-EI) Integrated 90-second maximum run timer UL325-2010 Monitored Entrapment Capability Monitored protection against transient overvoltage conditions 3-button control station included STANDARD FEATURES Motor: Powerful 1/2 HP single phase motor with instant reverse and internal automatic reset thermal overload. Removable without affecting limit switch settings. Auxiliary Reversal System: Designed to protect the door and door operator from damage; if a closing door strikes an obstruction the Auxiliary Reversal System will detect the slip of the clutch and reverse the door to the full open position. This system is not a substitute for a safety sensing device such as a photo cell or reversing edge. Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close. Momentary contact to close (B2 wiring) can be easily set, but requires the presence of either CPS-U CPS-UN4, or CPS-EI safety devices. The operator is pre-wired to accept a sensing device photoelectric control radio controls and most types of access control equipment. Rail Assembly: High strength dual L-rail track with exclusive nylon quiet gliding chain guides on rail spacers for quiet smooth operation. Includes quick-mount header bracket which provides fast swing-up installation. Operator/Motor Control: Solid-state Medium-Duty circuit board. Control Circuit: 24V NEC Class 2. Drive Reduction: First stage heavy-duty 4L V-belt; second and third stages #48 chain; output on trolley #48 chain. Emergency Disconnect: Spring-loaded disconnect for emergency manual operation. Push Button Station: 3-button station for OPEN/CLOSE/STOP functions is standard for all operators. Controls with 1, 2 and 3 buttons are available. Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with baked-on powder coat finish all reduction sprockets drilled and pinned to shafts. Bearings: Heavy-duty oil filled bearings. Radio Receiver: 315MHz radio receiver is integral to the Medium-Duty logic board. Accepts up to 20 Security remote controls and unlimited DIP switch remote controls. Friction Clutch: Adjustable friction clutch helps protect against damage to the door and operator should the door meet an obstruction. Works in conjunction with the Auxiliary Reversal System. Warranty: 2-year warranty. CONTROL ACCESSORIES AND OPTIONS Primary Monitored Entrapment Protection: The presence of primary entrapment protection is required for all modes and features beyond basic constant-pressure-to-close performance. Primary entrapment protection devices are monitored continuously to insure safe operation of the door and limit door operator functionality should an obstruction be detected or in the event of device failure. LiftMaster Monitored Entrapment Protection devices, CPS-U, CPS-UN4 and CPS-EI, are designed to work in conjunction with LiftMaster commercial door operators to provide enhanced door safety and a broad range of modes and features to end users. Either monitored photo-sensor or monitored 4-wire sensing edge (in conjunction with the CPS-EI Edge Interface) protection may be selected, but one must be detected by the LiftMaster Logic 4.0 or Medium-Duty Logic circuit board in order to unlock full functionality. Ancillary Entrapment Protection: (optional) LiftMaster Retro-Reflective Commercial Protector System photo sensors 2-wire non-monitored sensing edges and pneumatic sensing edges are considered secondary entrapment protection and may be used to supplement primary entrapment protction or basic constant-pressure-to-close. Solenoid Brake: Solenoid actuated brake prevents coasting. Order operator BMT. Standard on 3/4 HP and higher. Auto-Reconnect Trolley Assembly: Spring-loaded trolley features nylon inserts for quiet operation and auto-reconnect feature eliminating the need to manually reattach the door arm to the trolley after emergency disconnect. Radio Control: Universal transmitters and receivers are available to signal the operator to open and/or close. Key Switch: Designed to restrict operation of door to authorized personnel only. Various types available. Interlock Switch: Prevents accidental operation of the door by interrupting the control circuit.
Garage Door Mart is a trusted BBB certified garage door company serving the Naperville, Aurora, Plainfield and all Chicago-land garage door needs for over 10 years. Our customers value our quality services and have submitted numerous feedback comments over the years that we proudly present on our site. Click to read testimonials and what our customers are saying about us.
"Door Mart came really fast just to lift the door up so that I could drive my husband to the airport so he wouldn't miss his flight. Ash came back later the same afternoon and he only charged us for one service." read more testimonials.
Contact us today to have your free estimate our sales representative will help you to find out the style you're looking for and to be installed by one of our certified technicians professionally.